1.4 mm or 1.8 mm: Choosing Casement Wall Thickness by Wind Load and Glass Size - Siken Aluminum

1.4 mm or 1.8 mm: Choosing Casement Wall Thickness by Wind Load and Glass Size

Two numbers buyers compare, one decision

A casement window quotation almost always names the wall thickness of the profile before it names anything else: 1.4 mm or 1.8 mm. The number is easy to compare and easy to argue about, but on its own it says very little. What decides whether a window stays square for fifteen years is the combination of wall thickness, glass size and the way the two meet at the rebate.

This note sets out how we specify the two profiles we make most often, and where each one earns its place.

What the wall thickness actually does

The wall is the material thickness of the aluminium section itself. Increase it and the section resists bending and twisting more strongly for the same outer dimensions, which matters at the mullion and at the hinge side of an opening leaf. It also gives the fabricator more material to work with when the profile is machined for hardware, drainage slots and corner cleats.

Decrease it and the window becomes lighter and cheaper to move, and the same extrusion can be produced faster. Neither is better in the abstract. The question is what the window is being asked to carry.

Glass size decides more than wind does

Glass is the heaviest single item in a window. Weight rises with area and with thickness, so a large pane in a tall opening loads the leaf, the hinges and the frame far more than a small pane in the same elevation. A 1.4 mm wall that behaves well with a modest pane can feel soft under a much larger one, long before any wind pressure is considered.

That is why we specify by glass range first and by exposure second. Glass range is a fact the buyer already knows at quotation stage; exposure is often not settled until the facade design is fixed.

The two profiles side by side

Profile Wall thickness Glass range Typical use
SA-SL80 1.4 mm 5–20 mm Residential and light commercial casement and sliding windows with standard glazing
SA-CD75 1.8 mm up to 28 mm Larger leaves, thicker or laminated glass, higher exposure elevations
SA-DW70 Thermal break, 24 mm PA66 strip Uw ≤ 2.0 W/m²K Air-conditioned buildings where condensation and cooling load matter
SA-CW120 3.0 mm Curtain wall, wind load to 2.5 kPa Semi-exposed curtain wall where the frame carries the facade, not a wall

Where 1.4 mm is the right answer

For a house, an apartment block or a shopfront with openings up to a normal domestic size and glass inside the 5–20 mm range, the 1.4 mm section does the job. It keeps the leaf light enough to operate comfortably, it takes standard hardware without modification, and it leaves more of the budget for the glass and the installation — which is where most of the performance actually comes from.

Specifying 1.8 mm everywhere is not a safety margin. It is extra weight and extra cost carried by every leaf, including the small ones that never needed it.

Where 1.8 mm pays for itself

Three conditions move the decision to the heavier wall. The first is glass above 20 mm, including laminated build-ups, because the rebate has to be deeper and the leaf heavier. The second is a large opening leaf, where stiffness at the hinge side decides whether the window still closes cleanly after a few seasons. The third is an exposed elevation, where the frame is asked to hold shape under load rather than simply hold glass.

In each case the extra material is doing structural work. If none of the three applies, the heavier wall is buying reassurance rather than performance.

The hardware interface is where thin walls show

Hinges, espagnolettes and handles are fixed into the wall of the profile. A 1.4 mm wall accepts standard screw fixings correctly when the hardware is specified for that section. Problems appear when heavy-duty hardware designed for a 1.8 mm section is forced into a 1.4 mm profile, or when a fitter uses longer screws to compensate for a poor fit. That is an installation error, not a profile failure, and it is the most common cause of a hardware complaint we see.

What the thermal break changes

On an air-conditioned building the question is no longer only stiffness. A thermally broken profile with a 24 mm PA66 strip separates the inner and outer aluminium, which is what allows a window to reach Uw values of 2.0 W/m²K or better with the right glass. If condensation on the inner frame is the complaint, thicker walls will not fix it; the break will.

A short specification checklist

  • Fix the glass build-up and thickness first, then read the profile range against it.
  • Check the largest single pane, not the average: the heaviest leaf sets the requirement.
  • Decide whether the elevation is exposed before choosing between 1.4 mm and 1.8 mm.
  • Match hardware to the section it was designed for; do not compensate with longer fixings.
  • If cooling load or condensation is the driver, specify a thermal break rather than a heavier wall.

What we do not claim

Wall thickness alone does not determine a window’s wind resistance, watertightness or acoustic performance. Those depend on the complete system: profile geometry, hardware, gaskets, drainage and installation. A 1.8 mm profile badly assembled performs worse than a 1.4 mm profile assembled correctly. The numbers above describe what our profiles are made to carry; they are not a performance guarantee for a finished window.

Send the opening sizes, the glass build-up and the exposure of the elevation, and we will say which of the two sections fits — and say so plainly if neither does.

Category: Technical Guide

Leave a Comment

Your email address will not be published. Required fields are marked *

Contact Us  |  Email: info@sikenalshop.com  |  Tel: +86 137 8082 9852  |  WhatsApp: +86 137 8082 9852
FacebookYouTubeInstagramTikTokWhatsAppEmail
Economic Development Zone, Weifang, Shandong, China
Scroll to Top